Week 9-Creation of 1D Connectors Challenge

Aim-

     To create 1D element connector to given model, also to create mesh as per given criteria and to satisfy qualty criteria.

 Quality Criteria-

1D Connection type-

Procedure-

• Now we will firstly start with model import, for that import>>model import>>select model>>hit import.

• Now we will check for presence of solid as there is no solid present so we will move ahead.
• Now we will check for any topology error present in the surface and clear them manually.
•  Since we have cleared all the topological errors present in the geometry so we will go for criteria file setting.

• So we can go for meshing the parts one by one and also try to satisy quality criteria, for meshing Go to 2D>>Automesh>>Select target surface>>Element size-5>>Element type-mixed>>hit mesh.
• Try to reduce back to back trias formation and keep low tria concentraion.
• Now after mesh our components will look like as per below snap.

• Now we will check for quality criteria and if any element fails try to clear them.

• We can now check for free edges and resolve them, for that go to tool>>edges>>select element and create fee edges.
• Since there is no free edge present in the model so we can go ahead, for 1D Connector.

1. Right_Rail_2 & Front_truss_1:- Seam-Quad(angled+capped+L)

• Go to 1D>>Connectors>>seam>>type seam-quad (angled+clapped+L), select required nodes, components.
• spacing as 5, set weld ange, cap angle, tolerance as 15 and hit create.

• Again check for quality criteria and if there is no any problem then proceed again.

2. Left_Rail_2 & Front_truss_1:- Quad elements

• Go to 1D>>Connectors>>seam>>type seam-quad, select required nodes, components.
• spacing as 5, set tolerance as 15 and hit create.

3. Front_truss_2, Front_truss_1 & Right_Rail_1:- Spot weld with 3 Layers and 5 mm Diameter

• Go to 1D>>Connectors>>spot>>type weld, select required nodes, components, layers-total 3
• diameter as 5, tolerance as 15 and hit create.

4. Front_truss_2, Front_truss_1 & Left_Rail_1:- Hexa (Adhesive)

• Go to 1D>>Connectors>>seam>>type hexa (adhesive), select required nodes, components.
• spacing as 5, set tolerance as 15 and hit create, refer below snap.

5. Rear_truss_2 & Right_Rail_2:- Bolt Connector

• Go to 1D>>Connectors>>bolts>>type bolt (general), select required nodes, components.
• Set tolerance as 15, select create holes if none, and hit create, refer below snap.

6. Rear_truss_2 & Left_Rail_2:- Bolt Connector

• Go to 1D>>Connectors>>bolts>>type bolt (general), select required nodes, components.
• Set tolerance as 15, select create holes if none, and hit create, refer below snap.

7. Right_Rail_1 & Right_Rail_2:- Spot-weld with Rigid Elements

• Go to 1D>>Connectors>>spot>>type rigid, select required nodes, components, layers-total 2
• tolerance as 15, use diameter mapping and hit create.

8. Left_Rail_1 & Left_Rail_2:- Spot-weld with Spring Elements

• Go to 1D>>Connectors>>spot>>type rigid, select required nodes, components, layers-total 2
• tolerance as 15, use diameter mapping and hit create.

• Now we will connect rest of element with suitable connector and go for element check and also for duplicates.

• For check duplicate either go to tool>>elem check>>duplicates or by shrink element view.

 

• Now we will do final quality check.

Conclusion-

• Learnt about the 1D Connectors of different type and how mesh quality depends and changes with connector.