Procedure to draw p-1 :By absolute coordinate system Give a LINE command in autocad; LINE Specify first point : 2,1 Specify next point: 8,1 Specify next point : 8,2 Specify next point : 3,2 Specify next point : 3,6 Specify next point : 8,6 Specify next point : 8,7 Specify next point : 2,7 Specify next point : 2,1 or c…
AMOL KHEDEKAR
updated on 14 Aug 2022
Project Details
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Read more Projects by AMOL KHEDEKAR (28)
Reinforcement Detailing of Beams from ETABS output
Reinforcement Detailing of Beams from ETABS output Question: Detail design of beams in Etabs 2018.The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment ResistingFrame. The following challenge deals specifically with two continuous beams in the 1st floor. 1) 3 span continuous…
17 Dec 2022 05:21 PM IST
Project 1_Comparative study of different storey buildings for Seismic forces
Project 1 on _ Comparative study of different storey buildings for Seismic forces Factors influencing the dynamic characteristics of a building Answer:- Buildings oscilate during the earthquake shaking. The oscilation causes the inertia force to be induced in the building. The intensity and the duration of the oscilation…
09 Dec 2022 09:55 AM IST
Modelling of 25 storey building with the specified properties using ETABS
Challenge on: Modelling of 25 storey building with the specified properties using ETABS Model a 25 storey building on ETABS with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey…
06 Dec 2022 09:37 AM IST
Conceptual design of a building with columns and shear walls
CHALLENGE ON:-Conceptual design of a building with columns and shear walls Question 1:The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional…
03 Dec 2022 02:07 AM IST
Concept on positioning of Columns
CHALLENGE 4: Concept on positioning of Columns Question 1: Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness…
28 Nov 2022 03:55 AM IST
Understanding the concepts on Degrees of Freedom
Challenge 3: Understanding the concepts on Degrees of Freedom Question 1: A five storey structure with 5 translational DOF is shown here. Each storey has mass ‘m’. The eigenvalue problem has been solved and the 5 periods of vibration Tn and their…
26 Nov 2022 01:39 AM IST
Usage of Navigation tool , Timeliner and Clash Detection test using Naviswork
Revit Project 4 : Usage of Navigation tool , Timeliner and Clash Detection test using Naviswork 1) Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class Aim :- To Export…
23 Nov 2022 02:54 AM IST
Structural dynamics
Challenge 2 :- Structural dynamics Ans 1:Differentiate Static analysis and Dynamic analysis with proper representing pictures AIM-:1. Differentiate Static analysis and Dynamic analysis Ans.- Static Analysis Dynamic Analysis static analysis time invariant analysis…
11 Nov 2022 01:52 AM IST
Identification of Cracks
challenge 1: Identification of Cracks Question 1: What is the mode of failure or damage of the beams in the figure above? Are the damages repairable? Elaborate a) answer: Observation: In this picture we observe that, concrete get damaged/broken and reinforcement are visible at bottom of the beam.…
10 Nov 2022 12:35 PM IST
Creating Conceptual mass in REVIT and Creation of Sinusoidal curve and a Parametric stadium using Dynamo
PROJECT ON :- Creating Conceptual mass in REVIT and Creation of Sinusoidal curve and a Parametric stadium using Dynamo 1) Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. Answer:- Aim:- To create a set of sinusoidal points and to curve by using Dynamo.…
05 Nov 2022 10:42 AM IST
Creating Architectural and Structural model with 3D rendering using REVIT
PROJECT 2:- Creating Architectural and Structural model with 3D rendering using REVIT 1) Select the type of structure you want to build from one of the three below: a. Multi-Unit Residential Apartment b. Office Buildings …
21 Oct 2022 05:00 AM IST
3D Creation of Celing, Roof, Architectural plan, Structural plan, Sectional view, Elevation view and Camera specific view for a house plan using REVIT
REVIT CHALLENGE 4: 3D Creation of Celing, Roof, Architectural plan, Structural plan, Sectional view, Elevation view and Camera specific view for a house plan using REVIT 1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor…
11 Oct 2022 12:37 PM IST
Project 2_Creating a 3D rendered model for a Residential Building in AutoCad
AIM: Creating a 3D rendered model for a Residential Building in AutoCad PROJECT ON: 3D MODELLING AND RENDERING INTRODUCTION:- This complete project is all about the real 3D view of the models with the realistic materials, exposure, and lightning systems Tool used:- For 2D: line xline offset trim rec circle erase move…
21 Sep 2022 07:37 AM IST
Creating 3D Isometric view of various structural elements in AutoCAD
AIM:- Creating 3D Isometric view of various structural elements in AutoCAD Create a 3D Isometric View of the building with plan and elevation given. stepwise procedure:- command or tool used: For 2D: line offset trim explode rec move copy For 3D: Boundary region EXT pressfull subtract union move 3D rotate........ETC.…
17 Sep 2022 04:22 PM IST
Creating various 3D Models like Furniture, Footing, Girder, Column drop with panel and Gable Wall in AutoCad
AIM :-Creating various 3D Models like Furniture, Footing, Girder, Column drop with panel and Gable Wall in AutoCad 1. Create a 3D Furniture element as shown in the Figure. Assume dimensions which are missing. procedure : steps :- Open AutoCAD application open new drawing sheet set the unit Inches change…
12 Sep 2022 02:57 AM IST
Creation of Multiple viewports, Scaling the drawing and setting in Template in AutoCad
AIM :-Creation of Multiple viewports, Scaling the drawing and setting in Template in AutoCad 1:- Create a layout of the Plan and Section A of the project in Challenges 7, using the template Tutorial-mArch.dwt in a scale as given in the Figure. Use the MV command to create the viewport of the size as shown in Figure.…
10 Sep 2022 01:23 PM IST
Creating Kitchen layout, Hatching of Architectural elements and sectional view of an Industrial Building in AutoCad
AIM :-Creating Kitchen layout, Hatching of Architectural elements and sectional view of an Industrial Building in AutoCad PROBLEM 1 :Create the layouts of the Kitchen and provide hatches pattern as shown. Also, use blocks wherever required. Provide appropriate dimensions in the plan. Assume the size of doors, appliances…
09 Sep 2022 08:01 AM IST
Creating Bar Bending schedule, Different Door types, and Creation of standard drawing templates using AutoCad
AIM:-Creating Bar Bending schedule, Different Door types, and Creation of standard drawing templates using AutoCad PROBLEM NO 1:- Create the templates as shown in Figures. Take the size of the title block as per industry standards or you can assume it as per the size of the paper. Use text and attributes wherever required.…
08 Sep 2022 11:09 AM IST
Project 1 _Creating an Architectural plan for the provided plot size and develop relevant basic structural drawings
PROJECT ON: Creating an Architectural plan for the provided plot size and develop relevant basic structural drawings AIM:- To Design and Draft a layout of a residential building with the following details: a. Plot Size: 60’x20’(18.3m x6m) b. Orientation- Facing East c. Develop the…
06 Sep 2022 10:13 AM IST
Creating a Layout, Section and Elevation with dimensions using AutoCad
Creating a Layout, Section and Elevation with dimensions using AutoCad Aim:- Create the Plan and Sections as shown in the Figures. Use proper dimension techniques and dimension styles to document the project. Assume the sizes of the doors and windows as per construction…
05 Sep 2022 07:04 AM IST
Creating a Wardrobe detailed drawing, Floor Plan, Kitchen Layout and Column Detail using AutoCad
Creating the Wardrobe Detailed Drawing, Floor Plan, Kitchen Layout and Column Details by Using the AutoCAD. 1.Aim:-To…
03 Sep 2022 04:52 AM IST
Creation of Column Schedule and Drawing Template using AutoCad
Creation of column schedule and Drawing Templates using AutoCAD. 1. Aim and Introduction:- To create the column schedule using line tool and Dtext command. Procedure:- Steps: Taake the line command and offset command draw the table Trim all unwanted lines use Dtext command justify at left Specify…
25 Aug 2022 02:21 AM IST
Creating a Residence Layout, Seating plan, Toilet and Utility room plan using AutoCad
Creating the Residence Layout, Seating plan, Toilet and Utility Room in the AutoCAD. 1.Aim:- To crate or draw the Residence Plan in AutoCAD. Introduction:- The Residential plan or a layout consisting the following units/parts: Two Bedrooms Two Toilets A kitchen Dining Room Living…
24 Aug 2022 04:39 AM IST
Drafting of various geometries using Chamfer, Fillet tool in AutoCad
Drafting of various geometries using chamfer, fillet tool in AutoCAD. 1.Aim: To draft the given geometries in Decimal unit in AutoCAD. procedure to draft; Initially set the unit as decimal by using UNIT command. Choose the line command. specify first point as 0,0 specify next point as @3<0 specify next point as…
21 Aug 2022 02:56 PM IST
Creating a Floor plan, Footing detail and Isometric view using AutoCad
Challenge NO.2 Ans-1. Aim: To draw the Foundation of L.B.S showing plinth height, steps, wall Procedure to draw: Line command-Enter-specify first point: Click anywhere on the autocad drawing sheet where u want to start; Specify next point :…
18 Aug 2022 07:11 AM IST
Creation of geometries by Coordinate system methods using AutoCad
Procedure to draw p-1 :By absolute coordinate system Give a LINE command in autocad; LINE Specify first point : 2,1 Specify next point: 8,1 Specify next point : 8,2 Specify next point : 3,2 Specify next point : 3,6 Specify next point : 8,6 Specify next point : 8,7 Specify next point : 2,7 Specify next point : 2,1 or c…
14 Aug 2022 04:58 PM IST
Sketch a G+1 residential plan according to Vaastu Shastra and Calculation of Loads as per IS code
Aim : TO sketch a G+1 residential plan, according to Vaastu shastra, and list down the names of the structural drawings required to be provided to the site for construction. Also, assume the sizes of the structural elements (column, beam, slab, etc.) and accordingly calculate the individual corresponding…
08 Aug 2022 03:20 PM IST
Project on Concrete Mix Design for various grades of Concrete
Project on : Concrete Mix Design for various grades of concrete Aim: concrete mix design for M35 grade concrete with fly ash Objective: To make a concrete mix workable for the different structural members of building by selecting proper proportion of concrete ingredients, through this selection of proper…
07 Aug 2022 03:05 PM IST