Creating Architectural and Structural model with 3D rendering using REVIT

Reinforcement Detailing of Beams from ETABS output Question: Detail design of beams in Etabs 2018.The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment ResistingFrame. The following challenge deals specifically with two continuous beams in the 1st floor.         1) 3 span continuous…

  Project 1 on _ Comparative study of different storey buildings for Seismic forces Factors influencing the dynamic characteristics of a building Answer:- Buildings oscilate during the earthquake shaking. The oscilation causes the inertia force to be induced in the building. The intensity and the duration of the oscilation…

  Challenge on: Modelling of 25 storey building with the specified properties using ETABS   Model a 25 storey building on ETABS with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey…

CHALLENGE ON:-Conceptual design of a building with columns and shear walls Question 1:The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional…

  CHALLENGE 4:         Concept on positioning of Columns Question 1: Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness…

            Challenge 3:   Understanding the concepts on Degrees of Freedom   Question 1: A five storey structure with 5 translational DOF is shown here. Each storey has mass ‘m’. The eigenvalue problem has been solved and the 5 periods of vibration Tn and their…

Revit Project 4 : Usage of Navigation tool , Timeliner and Clash Detection test using Naviswork    1) Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class  Aim :- To Export…

Challenge 2 :-               Structural dynamics Ans 1:Differentiate Static analysis and Dynamic analysis with proper representing pictures AIM-:1. Differentiate Static analysis and Dynamic analysis  Ans.- Static Analysis Dynamic Analysis  static analysis time invariant analysis…

challenge 1: Identification of Cracks   Question 1: What is the mode of failure or damage of the beams in the figure above? Are the damages repairable? Elaborate a) answer:      Observation: In this picture we observe that, concrete get damaged/broken and reinforcement are visible at bottom of the beam.…

  PROJECT ON :- Creating Conceptual mass in REVIT and Creation of Sinusoidal curve and a Parametric stadium using Dynamo   1) Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. Answer:- Aim:- To create a set of sinusoidal points and to curve by using Dynamo.…

 PROJECT 2:-        Creating Architectural and Structural model with 3D rendering using REVIT 1) Select the type of structure you want to build from one of the three below:         a. Multi-Unit Residential Apartment         b. Office Buildings  …

REVIT CHALLENGE 4: 3D Creation of Celing, Roof, Architectural plan, Structural plan, Sectional view, Elevation view and Camera specific view for a house plan using REVIT 1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor…

AIM: Creating a 3D rendered model for a Residential Building in AutoCad PROJECT ON: 3D MODELLING AND RENDERING  INTRODUCTION:- This complete project is all about the real 3D view of the models with the realistic materials, exposure, and lightning systems Tool used:- For 2D:  line  xline  offset trim rec circle erase move…

AIM:-   Creating 3D Isometric view of various structural elements in AutoCAD Create a 3D Isometric View of the building with plan and elevation given. stepwise procedure:- command or tool used: For 2D: line offset trim explode rec move copy For 3D: Boundary region EXT pressfull subtract union move  3D rotate........ETC.…

AIM :-Creating various 3D Models like Furniture, Footing, Girder, Column drop with panel and Gable Wall in AutoCad 1. Create a 3D Furniture element as shown in the Figure. Assume dimensions which are missing. procedure : steps :- Open AutoCAD application open new drawing sheet  set the unit Inches change…

AIM :-Creation of Multiple viewports, Scaling the drawing and setting in Template in AutoCad 1:- Create a layout of the Plan and Section A of the project in Challenges 7, using the template Tutorial-mArch.dwt in a scale as given in the Figure. Use the MV command to create the viewport of the size as shown in Figure.…

AIM :-Creating Kitchen layout, Hatching of Architectural elements and sectional view of an Industrial Building in AutoCad PROBLEM 1 :Create the layouts of the Kitchen and provide hatches pattern as shown. Also, use blocks wherever required. Provide appropriate dimensions in the plan. Assume the size of doors, appliances…

 AIM:-Creating Bar Bending schedule, Different Door types, and Creation of standard drawing templates using AutoCad   PROBLEM NO 1:- Create the templates as shown in Figures. Take the size of the title block as per industry standards or you can assume it as per the size of the paper. Use text and attributes wherever required.…

  PROJECT ON: Creating an Architectural plan for the provided plot size and develop relevant basic structural drawings AIM:- To Design and Draft a layout of a residential building with the following details: a. Plot Size: 60’x20’(18.3m x6m)  b. Orientation- Facing East    c. Develop the…

              Creating a Layout, Section and Elevation with dimensions using AutoCad Aim:- Create the Plan and Sections as shown in the Figures. Use proper dimension techniques and dimension styles to document the project. Assume the sizes of the doors and windows as per construction…

            Creating the Wardrobe Detailed Drawing, Floor Plan, Kitchen Layout and                                              Column Details by Using the AutoCAD.   1.Aim:-To…

   Creation of column schedule and Drawing Templates using AutoCAD. 1. Aim and Introduction:- To create the column schedule using line tool and Dtext command. Procedure:- Steps: Taake the line command and offset command draw the table Trim all unwanted lines use Dtext command  justify at left  Specify…

        Creating the Residence Layout, Seating plan, Toilet and Utility Room in the AutoCAD. 1.Aim:- To crate or draw the Residence Plan in AutoCAD.   Introduction:-  The Residential plan or a layout consisting the following units/parts: Two Bedrooms Two Toilets A kitchen Dining Room Living…

Drafting of various geometries using chamfer, fillet tool in AutoCAD. 1.Aim: To draft the given geometries in Decimal unit in AutoCAD. procedure to draft; Initially set the unit as decimal by using UNIT command. Choose the line command. specify first point as 0,0 specify next point as @3<0 specify next point as…

Challenge NO.2 Ans-1. Aim:  To draw the Foundation of L.B.S showing plinth height, steps, wall            Procedure to draw:    Line command-Enter-specify first point: Click anywhere on the autocad drawing sheet where u want to start; Specify next point :…

Procedure to draw p-1 :By absolute coordinate system Give a LINE command in autocad; LINE Specify first point : 2,1 Specify next point: 8,1 Specify next point : 8,2 Specify next point : 3,2 Specify next point : 3,6 Specify next point : 8,6 Specify next point : 8,7 Specify next point : 2,7 Specify next point : 2,1 or c…

  Aim :   TO sketch a G+1 residential plan, according to Vaastu shastra, and list down the names of the structural drawings required to be provided to the site for construction. Also, assume the sizes of the structural elements (column, beam, slab, etc.) and accordingly calculate the individual corresponding…

Project on : Concrete Mix Design for various grades of concrete   Aim: concrete mix design for M35 grade concrete with fly ash Objective:  To make a concrete mix workable for the different structural members of building  by selecting proper proportion of concrete ingredients, through this selection of proper…