Writing A MATLAB/Octave Program To Solve the 2D Heat Conduction Equation For Both Steady & Transient State Using Jacobi, Gauss-Seidel & Successive Over Relaxation (SOR) Schemes.
Problem Statement:- 1. Steady-state analysis & Transient State Analysis Solve the 2D heat conduction equation by using the point iterative techniques that were taught in the class. The Boundary conditions for the problem are as follows; Top Boundary = 600 K Bottom Boundary = 900 K Left Boundary = 400 K Right Boundary…
Pratik Ghosh
updated on 19 Jan 2021
Problem Statement:-
1. Steady-state analysis & Transient State Analysis
Solve the 2D heat conduction equation by using the point iterative techniques that were taught in the class. The Boundary conditions for the problem are as follows;
Top Boundary = 600 K
Bottom Boundary = 900 K
Left Boundary = 400 K
Right Boundary = 800 K
You will implement the following methods for solving implicit equations.
1. Jacobi
2. Gauss-seidel
3. Successive over-relaxation
Your absolute error criteria is 1e-4
Abstract:- The work is focused on writing several MATLAB/Octave codes to solve steady & unsteady (transient) state 2D heat conduction equations by using the point iterative techniques such as Jacobi, Gauss-seidel & Successive Over Relaxation (SOR) for both implicit & explicit schemes. The problem statement requires us to assume that the domain is a square i.e. the number of node points along the X-axis is equal to the Y-axis. The necessary Boundary Conditions are provided to us as:- Top Boundary = 600 K, Bottom Boundary = 900 K, Left Boundary = 400Ti,j=dy2⋅(Ti+1,j+Ti-1,j)+dx2⋅(Ti,j+1+Ti,j-1)2⋅(dx2+dy2)">K, Right Boundary = 800 K. This project has been divided into two parts. Part 1, focuses on solving the problem using a Steady-state solver & then comparing the results for Jacobi, Gauss-seidel & Successive Over Relaxation (SOR) schemes. While Part 2, deals with solving the problem using a transient solver using both Implicit & Explicit methods & then compares the results for Jacobi, Gauss-seidel & Successive Over Relaxation (SOR) schemes.
Theory:-
Part 1: Steady-State Analysis of the 2D heat conduction
(∂2T∂x2)+(∂2T∂y2)=0
Next, we apply the central differencing scheme to discretize the equation
(∂2T∂x2)=Ti−1,j−2(Ti,j)+(Ti+1,j)Δx2
(∂2T∂y2)=Ti,j-1−2(Ti,j)+(Ti,j+1)Δy2
Adding the two equations we get
(∂2T∂x2)=Ti−1,j−2(Ti,j)+(Ti+1,j)Δx2+(∂2T∂y2)=Ti,j-1−2(Ti,j)+(Ti,j+1)Δy2=0
we know Nx=Ny=nodes on each sides are equal,
we can consider △x=△y, on rearranging we get
Ti,j=14(Ti−1,j+Ti+1,j+Ti,j−1+Ti,j+1)
MATLAB/Octave program code (Steady-state)
#Main Program code to solve the Steady-State 2D Heat Conduction problem
------------------------------------------------------------------------------------------------------------------------------------------------------------------
clear all
close all
clc
%inputs
nx = 10 % number of grid points along x axis
ny = nx ; %since given domain is a square
x = linspace(0,1,nx);
dx = x(2)-x(1);
y = linspace(0,1,ny);
z = fliplr(y);
f = 1.5;
iter = 1;
t = ones([nx,ny])*298;
% Applying the given Boundary Conditions
t(1,1:nx) = 600;
t(ny,1:nx) = 900;
t(2:ny-1,1) = 400;
t(2:ny-1,nx) = 800;
% Creating a copy
told = t;
r1 = t;
error = 19;
tol = 1e-4;
for iterative_solver=1:3;
while(error>tol);
for i=2:nx-1;
for j=2:ny-1;
if(iterative_solver==1);
t(i,j)=jacobi(t,told,i,j);
elseif(iterative_solver==2)
t(i,j)=GS(t,told,i,j);
else
t(i,j)=sor(t,told,i,j,f);
end
end
end
error = max(max(t-told));
told = t;
[u1,v1] = meshgrid(x,z);
%plotting the contours
if(iterative_solver==1);
figure (1);
contourf(u1,v1,t);
[C,h]=contourf(u1,v1,t);
colorbar;
colormap(jet);
clabel(C,h);
xlabel('x-axis');
ylabel('y-axis');
title_text=sprintf('jacobi iterantion number = %d',iter);
title(title_text);
pause(0.003);
elseif(iterative_solver==2);
figure (2);
contourf(u1,v1,t);
[C,h]=contourf(u1,v1,t);
colorbar;
colormap(jet);
clabel(C,h);
xlabel('x-axis');
ylabel('y-axis');
title_text=sprintf('GS iterantion number = %d',iter);
title(title_text);
pause(0.003);
else
figure (3);
[C,h]=contourf(u1,v1,t);
colorbar;
colormap(jet);
clabel(C,h);
xlabel('x-axis');
ylabel('y-axis');
title_text=sprintf('sor iterantion number = %d',iter);
title(title_text);
pause(0.003);
end
iter = iter+1;
end
error = 19;
iter = 1;
t = r1;
told = r1;
end #User Defined Function (UDF) for Steady-State Jacobi scheme
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------
function out = jacobi(t,told,i,j)
out=0.25*((told(i,j-1)+told(i,j+1)+told(i-1,j)+told(i+1,j)));
end #User Defined function(UDF) for Gauss-Seidal Scheme
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
function out = GS(t,told,i,j)
out=0.25*(t(i,j-1)+told(i,j+1)+t(i-1,j)+told(i+1,j));
end #User Defined Function (UDF) for Steady-State Successive Over Relaxation(SOR) scheme
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------
function out = sor(t,told,i,j,f)
out =((1-f)*told(i,j)+(f*0.25*(t(i,j-1)+told(i,j+1)+t(i-1,j)+told(i+1,j))));
end
Observations & Conclusion (Steady-state) :-
_1608566442.png)
_1608566526.png)
_1608566462.png)
From the above three contour plots, we can conclude that for steady-state analysis of a 2D heat conduction problem the Successive Over Relaxation (SOR) Scheme requires much lower iterations to reach the desired solution than Gauss-Siedel & Jacobi schemes which took 111 & 207 iterations respectively. The number of iterations & stability of the solution depends on the relaxation factor for SOR. If the relaxation factor reaches a value of 0 then it will lead to under-relaxation which would then again increase the number of iterations, vice versa if the relaxation factor is high then it will lead to the solution to blow off.
Part 2: Unsteady/Transient State Analysis of the 2D heat conduction (Explicit & Implicit)
(i) Solving using Explicit Method
The 2-D heat equation for an unsteady/transient state is given by,
MATLAB/Octave program code (Transient-state, Explicit)
#Main Program code to solve the Transient/Unsteady state 2D Heat Conduction problem (Explicit Scheme)
---------------------------------------------------------------------------------------------------------------------------------------------------------------------
close all
clear all
clc
%Solving the Unsteady state 2D heat conduction (EXPLICIT SCHEME)
%Input Parameters
%Number of grid points
nx = 10;
ny = nx;
nt = 1400;
x = linspace(0,1,nx);
y = linspace(0,1,ny);
dx = x(2) - x(1);
dy = dx;
%Absolute error criteria > tolerance
error = 9e9;
tolerance = 1e-4;
dt = 1e-3;
omega = 1.1;
%Defining Boundary conditions
T_L = 400;
T_T = 600;
T_R = 800;
T_B = 900;
T = 300*ones(nx,ny);
T(2:ny - 1, 1) = T_L;
T(2:ny - 1, nx) = T_R;
T(1, 2:nx - 1) = T_T;
T(ny, 2:nx - 1) = T_B;
%Calculating Average temperature at corners
T(1,1) = (T_T + T_L)/2;
T(nx,ny) = (T_R + T_B)/2;
T(1,ny) = (T_T + T_R)/2;
T(nx,1) = (T_L + T_B)/2;
%Assigning orginal values to T
T_intial = T;
T_old = T;
%Calculation of 2D steady heat conduction EQUATION by Successive over-relaxation method
iterative_solver = 1;
k1 = 1.1*(dt/(dx^2));
k2 = 1.1*(dt/(dy^2));
if iterative_solver == 1
Steady_Explicit = 1;
for k = 1:nt
error = 1;
while(error > tolerance)
for i = 2:nx - 1
for j = 2:ny - 1
Term_1 = T_old(i,j);
Term_2 = k1*(T_old(i+1,j) - 2*T_old(i,j) + (T_old(i-1,j)));
Term_3 = k2*(T_old(i,j+1) - 2*T_old(i,j) + T_old(i,j-1));
T(i,j) = Term_1 + Term_2 + Term_3;
end
end
error = max(max(abs(T_old - T)));
T_old = T;
Steady_Explicit = Steady_Explicit + 1;
end
end
end
%Plotting
figure(1)
contourf(x,y,T)
clabel(contourf(x,y,T))
colorbar
colormap(jet)
set(gca, 'ydir', 'reverse')
xlabel('X-Axis')
ylabel('Y-Axis')
title(sprintf('No. of Unsteady Iterations(EXPLICIT) = %d', Steady_Explicit));
pause(0.03);
Results:-
_1608576757.png)
(ii) Solving using Implicit Method
MATLAB/Octave program code for Jacobi Scheme (Transient-state, Implicit)
#MATLAB/Octave code for solving Unsteady/Transient state 2D heat conduction by Jacobi Method (IMPLICIT SCHEME)
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
close all
clear all
clc
%Input Parameters
%Number of grid points
nx = 10;
ny = nx;
nt = 1400;
x = linspace(0,1,nx);
y = linspace(0,1,ny);
dx = x(2) - x(1);
dy = dx;
%Absolute error criteria > tolerance
error = 9e9;
tolerance = 1e-4;
dt = 1e-3;
%Defining Boundary conditions
T_L = 400;
T_T = 600;
T_R = 800;
T_B = 900;
T = 300*ones(nx,ny);
T(2:ny - 1, 1) = T_L;
T(2:ny - 1, nx) = T_R;
T(1, 2:nx - 1) = T_T;
T(ny, 2:nx - 1) = T_B;
%Calculating Average temperature at corners
T(1,1) = (T_T + T_L)/2;
T(nx,ny) = (T_R + T_B)/2;
T(1,ny) = (T_T + T_R)/2;
T(nx,1) = (T_L + T_B)/2;
%Assigning orginal values to T
T_old = T;
T_intial = T;
%Calculation of 2D steady heat conduction EQUATION by Successive over-relaxation method
k1 = 1.1*(dt/(dx^2));
k2 = 1.1*(dt/(dy^2));
Jacobi_iteration = 1;
for k = 1:nt
error = 9e9;
while(error > tolerance)
for i = 2:nx - 1
for j = 2:ny - 1
Term_1 = 1/(1 + (2*k1) + (2*k2));
Term_2 = k1*Term_1;
Term_3 = k2*Term_1;
H = (T_old(i-1,j)) + (T_old(i+1,j));
V = (T_old(i,j+1)) + (T_old(i,j-1));
T(i,j) = (T_intial(i,j)*Term_1) + (H*Term_2) + (V*Term_3);
end
end
error = max(max(abs(T_old - T)));
T_old = T;
Jacobi_iteration = Jacobi_iteration + 1;
end
T_intial = T;
%Plotting
figure(1)
contourf(x,y,T)
clabel(contourf(x,y,T))
colorbar
colormap(jet)
set(gca, 'ydir', 'reverse')
xlabel('X-Axis')
ylabel('Y-Axis')
title(sprintf('No. of Unsteady Jacobi Iterations(IMPLICIT) = %d', Jacobi_iteration));
pause(0.03)
end
MATLAB/Octave program code for Gauss-Siedel (Transient-state, Implicit)
#MATLAB/Octave code for solving Unsteady/Transient state 2D heat conduction by Gauss-seidel Method (IMPLICIT SCHEME)
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------
close all
clear all
clc
%Input Parameters
%Number of grid points
nx = 10;
ny = nx;
nt = 1400;
x = linspace(0,1,nx);
y = linspace(0,1,ny);
dx = x(2) - x(1);
dy = dx;
%Absolute error criteria > tolerance
error = 9e9;
tolerance = 1e-4;
dt = 1e-3;
%Defining Boundary conditions
T_L = 400;
T_T = 600;
T_R = 800;
T_B = 900;
T = 300*ones(nx,ny);
T(2:ny - 1, 1) = T_L;
T(2:ny - 1, nx) = T_R;
T(1, 2:nx - 1) = T_T;
T(ny, 2:nx - 1) = T_B;
%Calculating Average temperature at corners
T(1,1) = (T_T + T_L)/2;
T(nx,ny) = (T_R + T_B)/2;
T(1,ny) = (T_T + T_R)/2;
T(nx,1) = (T_L + T_B)/2;
%Assigning orginal values to T
T_old = T;
T_intial = T;
%Calculation of 2D steady heat conduction EQUATION by Successive over-relaxation method
k1 = 1.1*(dt/(dx^2));
k2 = 1.1*(dt/(dy^2));
Gauss_Seidel_iteration = 1;
for k = 1:nt
error = 9e9;
while(error > tolerance)
for i = 2:nx - 1
for j = 2:ny - 1
Term_1 = 1/(1 + (2*k1) + (2*k2));
Term_2 = k1*Term_1;
Term_3 = k2*Term_1;
H = (T(i-1,j)) + (T_old(i+1,j));
V = (T(i,j+1)) + (T_old(i,j-1));
T(i,j) = (T_intial(i,j)*Term_1) + (H*Term_2) + (V*Term_3);
end
end
error = max(max(abs(T_old - T)));
T_old = T;
Gauss_Seidel_iteration = Gauss_Seidel_iteration + 1;
end
T_intial = T;
%Plotting
figure(1)
contourf(x,y,T)
clabel(contourf(x,y,T))
colorbar
colormap(jet)
set(gca, 'ydir', 'reverse')
xlabel('X-Axis')
ylabel('Y-Axis')
title(sprintf('No. of Unsteady Gauss-Seidel Iterations(IMPLICIT) = %d', Gauss_Seidel_iteration));
pause(0.03)
end
MATLAB/Octave program code for SOR (Transient-state, Implicit)
#MATLAB/Octave code for solving Unsteady/Transient state 2D heat conduction by Successive over-relaxation Method (SOR)(IMPLICIT SCHEME)
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------
close all
clear all
clc
%Input Parameters
%Number of grid points
nx = 10;
ny = nx;
nt = 1400;
x = linspace(0,1,nx);
y = linspace(0,1,ny);
dx = x(2) - x(1);
dy = dx;
%Absolute error criteria > tolerance
error = 9e9;
tolerance = 1e-4;
dt = 1e-3;
omega = 1.1;
%Defining Boundary conditions
T_L = 400;
T_T = 600;
T_R = 800;
T_B = 900;
T = 300*ones(nx,ny);
T(2:ny - 1, 1) = T_L;
T(2:ny - 1, nx) = T_R;
T(1, 2:nx - 1) = T_T;
T(ny, 2:nx - 1) = T_B;
%Calculating Average temperature at corners
T(1,1) = (T_T + T_L)/2;
T(nx,ny) = (T_R + T_B)/2;
T(1,ny) = (T_T + T_R)/2;
T(nx,1) = (T_L + T_B)/2;
%Assigning orginal values to T
T_old = T;
T_intial = T;
T_end = T;
%Calculation of 2D steady heat conduction EQUATION by Successive over-relaxation method
k1 = 1.1*(dt/(dx^2));
k2 = 1.1*(dt/(dy^2));
Successive_over_relaxation_iteration = 1;
for k = 1:nt
error = 9e9;
while(error > tolerance)
for i = 2:nx - 1
for j = 2:ny - 1
Term_1 = 1/(1 + (2*k1) + (2*k2));
Term_2 = k1*Term_1;
Term_3 = k2*Term_1;
H = (T(i-1,j)) + (T_old(i+1,j));
V = (T(i,j+1)) + (T_old(i,j-1));
T(i,j) = (T_intial(i,j)*Term_1) + (H*Term_2) + (V*Term_3);
T_end(i,j) = ((1-omega)*T_old(i,j)) + (T(i,j)*omega);
end
end
error = max(max(abs(T_old - T)));
T_old = T_end;
Successive_over_relaxation_iteration = Successive_over_relaxation_iteration + 1;
end
T_intial = T_end;
%Plotting
figure(1)
contourf(x,y,T)
clabel(contourf(x,y,T))
colorbar
colormap(jet)
set(gca, 'ydir', 'reverse')
xlabel('X-Axis')
ylabel('Y-Axis')
title(sprintf('No. of Unsteady SOR Iterations(IMPLICIT) = %d', Successive_over_relaxation_iteration));
pause(0.03)
end
Observations & conclusion:-
_1608617602.png)
_1608612328.png)
_1608617492.png)
From the plots above we can observe that using a transient solver requires a larger number of iterations to converge than a steady-state solver. We can also notice that the Successive Over Relation (SOR) scheme takes a lower number of iterations to converge than Jacobi & Gauss-Siedel schemes. Therefore we can make a final conclusion that the steady-state solver yields quicker results & that the SOR technique is more effective for the 2D heat conduction problem as it can reach convergence sooner using both steady & transient solver.
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Be the first to add a comment
Read more Projects by Pratik Ghosh (34)
Visualize 2D Flow Simulation Through A Backward Facing Step For 3 Distinct Mesh Grid Size Using openFOAM & ParaView
Abstract:- The work is focused on simulating fluid flow through a backward-facing step channel that would be subjected to a sudden increase in the cross-sectional area, this would result in flow separation & reattachment zones. The geometry will be designed by creating vertices & then joining them to form blocks.…
19 Jan 2021 06:26 AM IST
Week 12 - Symmetry vs Wedge vs HP equation
Objective:- The work is focused on performing a CFD simulation for a flow through a cylindrical pipe with reference to Hagen Poiseuille's principle that refers to the laminar flow formation inside a smooth cylindrical tube. Since the computation will be carried out on a laptop, we will not be able to consider the entire…
19 Jan 2021 06:26 AM IST
Writing A MATLAB/Octave Code To Perform A 1D Super-Sonic Nozzle Flow Simulation Using Macormack Method.
Abstract:- The work is focused on writing a MATLAB/Octave code to simulate the isentropic flow through a quasi 1D supersonic nozzle using both the conservation and non-conservation forms of the governing equations and solving them using MacCormack's technique and compare their solutions by performing a grid dependency…
19 Jan 2021 06:24 AM IST
Writing A MATLAB/Octave Program To Solve the 2D Heat Conduction Equation For Both Steady & Transient State Using Jacobi, Gauss-Seidel & Successive Over Relaxation (SOR) Schemes.
Problem Statement:- 1. Steady-state analysis & Transient State Analysis Solve the 2D heat conduction equation by using the point iterative techniques that were taught in the class. The Boundary conditions for the problem are as follows; Top Boundary = 600 K Bottom Boundary = 900 K Left Boundary = 400 K Right Boundary…
19 Jan 2021 06:23 AM IST
Related Courses
