AIM: To Create the Base Bracket Plastic component through the given Class-A surface by using Catia V5. OBJECTIVE: Create a tooling axis following the OEM standard Making the Surface into Solid Feature Create the Heat Stakes and the locators considering the design rules. Performing the draft analysis to the component…
Manivannan L
updated on 25 Apr 2021
Project Details
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Read more Projects by Manivannan L (29)
Design of backdoor
Aim: To design a backdoor of the car on sheet metal using the appropriate design and provided skin data by considering design parameters. Objective: To design a back door of a car with an inner panel, outer panel and reinforcement for hinges, gas stay, Wiper motor and latch. The inner panel is subjected to the draft…
08 Aug 2022 06:03 AM IST
Roof challenge
Aim: To a given roof styling, create essential flanges and reinforcement. Objective: To design the automotive roof based on the given styling surface and to analyze the prepared model to check the manufacturability and the feasibility of the design. To perform the section modulus study for the master sections and…
03 Aug 2022 01:31 PM IST
Section Modulus calculation and optimization
Aim: To find the section modulus of the hood and optimization to improve the overall section modulus. Objective: Use the section from your Hood design and calculate the section modulus using the formula S= I/y. Section Modulus: The section modulus (S) is geometry property of the cross section used for designing…
20 Jun 2022 09:40 AM IST
Fender Design Challenge
Aim: To design the car fender according to the given design parameter related to industry standard. Objective: To develop the front fender according to Euro Standards. Follows Design rules, inorder to satisfy the DFM & DFA. Introduction: …
10 Jun 2022 03:07 AM IST
Fender Design - Wheel Arch Challenge
Aim: To calculate the Fender Wheel Arch area , to pass the European standards. Objective: Create the intersection point according to given degree angle. Follow the European standards to prove the design is valid. …
29 Apr 2022 04:39 PM IST
Hood design-Week 2
Aim: Design the Hood Outer panel, Inner panel and other necessary reinforcements by following the Master Structure and design Parameter. Objective: To understand the design approach and its consideration that follows the designing and developing an automobile hood to ensure the pedestrian for inner and around the…
27 Apr 2022 04:48 PM IST
Underbody Coating
Aim: A brief study on Underbody Coating of an car. Objective: To obtain a study on underbody coating To prepare deatailed report by discussing its types, Pros and Cons. Introduction: Underbody Coating: Underbody coating is usually a dense cladding (often based on rubber)…
21 Sep 2021 05:48 PM IST
Benchmarking
Aim: To conduct the brief analysis on benchmarking on five seater family car. Objective: To conduct a case study on benchmarking on SUV car between 8 to 10 lakhs To obtain a brief on Benching Marking. Compare the selected car by their features, prices and performance. To arrive at a conclusion suggesting…
21 Sep 2021 05:03 PM IST
Project 2
Project 2 Design and modeling the Complete Tail lamp of the Car Aim: To create the a complete design of the tail lamp with all the assembly parts and child parts, also the attachment features by considering the design regulations in CATIA V5 Modelling Software. Objective: To the design the solid body tail lamp…
16 Sep 2021 11:52 AM IST
Project 1
Project 1 Aim: Creating the plastic component using the section. Objective: To create the solid plastic component using the master section. To obtain the same surface to the entire component without changing the given class A surface.…
16 Aug 2021 04:24 PM IST
Week 11 Challenge
Create one assembly drawing considering all factors Assembly drawing is a presentation of a structure or product with its components connected together, in their relative working positions while in use. These components are fabricated separately, and are assembled or installed together at their utility sites…
10 Aug 2021 03:22 PM IST
Week 11 - Final project
AIM: To design and development of vehicle interior door trim using Catia V5 with given class A surface along with Master section. Also create the Side Attachment features as per design rules. OBJECTIVE: To create thickened part using master section for reference To create the mounting features as per design guidelines…
19 May 2021 04:09 PM IST
Week 9 - Project - Master Section Development
AIM: To Create the B- pillar component with attachment features and add thickness to it by using Catia V5. OBJECTIVE: Create tooling axis and follow design rules. Follow the Master section to create flange Follow the master section for thickness and to create the closed volume. Follow master section…
25 Apr 2021 01:59 PM IST
Week 9 - Project 1 - Door Applique Design with Engineering Features
AIM: To Create the Base Bracket Plastic component through the given Class-A surface by using Catia V5. OBJECTIVE: Create a tooling axis following the OEM standard Making the Surface into Solid Feature Create the Heat Stakes and the locators considering the design rules. Performing the draft analysis to the component…
25 Apr 2021 07:04 AM IST
Week 8 - Challenge 5 - Core & Cavity Design
AIM: To create the core and cavity for Switch Bezel component through the given Class-A surface using Catia V5. OBJECTIVE: Create a tooling axis following the OEM standard Making the Surface into Solid Body Part Thickness : 2.5 mm Performing the draft analysis to the component INTRODUCTION:…
24 Apr 2021 07:30 AM IST
Week 9 - Attachment Feature Creation - Challenge 2
AIM: To create the Screw Bosses for the Centre console coin holder considering the design rules by using Catia V5. OBJECTIVE: Create a tooling axis following the OEM standard Making the Rib According to design rules Part Thickness : 40% NOMINAL VALUE and Draft angle : 0.5 Deg Performing the draft…
21 Apr 2021 06:00 PM IST
Week 9 - Attachment Feature Creation - Challenge 1
AIM: To create the rib formation for the Centre console coin holder considering the design rules by using Catia V5. OBJECTIVE: Create a tooling axis following the OEM standard Making the Rib According to design rules Part Thickness : 0.75 mm and Draft angle : 0.5 Deg Performing the draft analysis to…
21 Apr 2021 12:17 PM IST
Week 8 - Challenge 4 - Coin Holder Design
AIM: To Create the Coin Holder Plastic component through the given Class-A surface using Catia V5. OBJECTIVE: Create a tooling axis following the OEM standard Making the Surface into Solid Body Part Thickness : 2.5 mm Performing the draft analysis to the component INTRODUCTION: …
21 Apr 2021 09:25 AM IST
Door Arm Rest Week 8 Challenge
AIM: To Create the Door Arm rest Component and add thickness to it by using Catia V5. OBJECTIVE: Create a tooling axis following the OEM standard Making the Surface into Solid Body Part Thickness : 2.5 mm Performing the draft analysis to the component INTRODUCTION: …
21 Apr 2021 08:47 AM IST
Week 8 - Challenge 3 - Switch Bezel Design
Challenge : Creating the Switch Bezel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface will be created meeting the requirements of the draft angle and at the end of performing the Draft analysis on the model. Step : 1 In order to create the tooling…
29 Mar 2021 06:54 PM IST
Week 8 - Challenge 2 - Base Bracket Design
Challenge : Creating the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface will be created meeting the requirements of the draft angle and at the end of performing the Draft analysis on the model. Step : 1 In order to create the tooling…
29 Mar 2021 06:04 PM IST
Week 8 - Challenge 1 - Draft Analysis on a Fan Cover
Challenge: Creating the tooling axis for the given Fan cover model meeting the requirements of the draft angle and performing the Draft analysis for the model. Step 1: To create the tooling axis, initially ensuring the boundary of the fan cover model is fully enclosed. Step…
25 Mar 2021 05:51 AM IST
Challenge 12 : Rendering Project
Challenge 1: Aim : To create the photorealistic image for better visualization of the model. Objective : To render the model uisng the alias for the better understading of the product. Introduction: Visualization is known as a process of creating images, diagrams, or animations to communicate a message. Both abstract and…
11 Feb 2021 06:32 AM IST
Challenge 9 : Project : Technical Surfacing Kia Sportage
Title of the Project: Development of Kia sportage using Alias Auto Studio Objective To build the car using the Curves traced from the given blueprint of the car model. Introduction Concept Sculpting is more interesting and skill full work, where we can bring our design from paper sketch to 3D model. Concept sketch…
03 Feb 2021 05:49 AM IST
Challenge 8 : Concept Modeling of Seats
Title of the Project: Development of Car Seat using Alias Auto Studio Objective To build the seat of the car using the Curves traced from the given blueprint of the model. Introduction Surface modelling is the art of building complex geometrical features, one surface at a time. Usually surface modelling is used to…
08 Jan 2021 06:06 AM IST
Challenge 7 : Concept Modelling of Steering Wheel
Title of the Project: Development of Steering wheel of car using Alias Auto Studio Objective To build the steering wheel of the car using the Curves traced from the given blueprint of the model. Introduction Surface modelling is the art of building complex geometrical features, one surface at a time. Usually surface…
31 Dec 2020 09:21 AM IST
Challenge 6 : Concept Modeling of Side Fender
Title of the Project: Development of Front Fender part of car using Alias Auto Studio Objective To build the fender of the car using the Curves traced from the given blueprint of the model. Introduction Surface modelling is the art of building complex geometrical features, one surface at a time. Usually surface modelling…
22 Dec 2020 06:56 AM IST
Challenge 5 : Concept Modeling of Car Bumper
Challenge : 1 Title of the Project: Development of Front bumper of Abarth 500 using Alias Auto Studio Objective To build the Bumper of the car using the Curves traced from the given blueprint of the car model. Introduction Concept Sculpting is more interesting and skill full work, where we can bring our design from…
15 Dec 2020 04:37 PM IST
Challenge 4 : Concept Modelling of Alloy Wheel
Challenge 1: Title of the Project: Development of Alloy Wheel using Alias Auto Studio Objective To build the Surfaces using the Curves traced from the given blueprint of the alloy wheel. Introduction Concept Sculpting is more interesting and skill full work, where we can bring our design from…
05 Dec 2020 05:53 AM IST