Drop test Challenge Aim: - To create a complete simulation file to perform a drop test from a given basic .k file consisting of only nodes and elements. Essential keywords should be added to create a basic solver deck to simulate a drop test. Given: - Procedure: - Open the LS-PrePost and open the given keyword…
Parag Bari
updated on 23 Jul 2022
Project Details
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Read more Projects by Parag Bari (26)
Week - 3 Drop test Challenge
Drop test Challenge Aim: - To create a complete simulation file to perform a drop test from a given basic .k file consisting of only nodes and elements. Essential keywords should be added to create a basic solver deck to simulate a drop test. Given: - Procedure: - Open the LS-PrePost and open the given keyword…
23 Jul 2022 12:35 PM IST
Week - 2 - Explicit and Implicit Analysis
Aim: - To study about Implicit and explicit methods. Objectives: - As demonstrated in the PDF, F(u) = u3+9u2+4u use this equation and solve using both Explicit and Implicit Methods ( have a tolerence of 0.01) Explicit analysis: - Explicit analyses aim to solve for acceleration (or otherwise {x´´}).…
05 Jun 2022 11:57 AM IST
Final Quiz
1. What is the difference between the contents of Radioss Starter and Radioss Engine file in terms? ANSWER: - RADIOSS STARTER FILE: The starter file contains the model definition. Definitions like units, material, properties, nodal information, boundary conditions, interfaces, Load collectors, geometrical information,…
31 May 2022 07:05 AM IST
Assignment 8-Roof Crash Simulation Challenge
Assignment 8: - Roof Crash Simulation Aim - To run the roof crash simulation on the neon car model and plot the graphs for the neon car model in post-processing. Objective - To translate the impactor to the desired location as per the question. To create a Type 7 contact interface between impactor and car. To create a…
31 May 2022 06:09 AM IST
Assignment 7-Side Pole Crash Simulation Challenge
Assignment: - 7. Side Pole Crash Simulation Aim: To run a simulation for the Neon Side Pole Crash and to obtain the results in the post-processing. Objective: To check the unit system in the solver. To create an appropriate interface with friction 0.2 and recommended parameters. To check for the penetrations…
22 May 2022 01:03 PM IST
Assignment 6-Frontal Crash Simulation Challenge
Assignment 6:- Frontal Crash Simulation Aim - To run a simulation for the frontal crash [BIW] and to obtain a result in the post-processing. Objective - To check the unit system in the solver. To create an appropriate interface, friction 0.2 and recommended parameters. To check for the penetrations and intersections. To…
10 May 2022 04:52 PM IST
Assignment 5-RADIOSS Interfaces & Study of Effect of Notches Challenge
Assignment 5-RADIOSS Interfaces & Study of Effect of Notches Challenge Aim: - 1. Mesh the bumper assembly with mesh size 6mm. 2. Run the crash tube model with different cases. Objectives: - Model 1- Create the mesh for bumper assembly, mesh size should be 6mm. Model 2- Run the crash tube…
22 Mar 2022 11:29 AM IST
Assignment 4-RADIOSS Material Laws Challenge
Assignment 4-RADIOSS Material Laws Challenge Objectives: - Run the given model with different material parameters and compare all the cases. Materials: - The overview of the materials in the RADIOSS library can be classified as shown below: We will have a look at the following material laws: Law 1 – Elastic…
21 Mar 2022 05:24 AM IST
Week - 1 - Consistency of Units
Consistency of Units Objectives: - Write the given measurements of the following different systems of units. Also, mention the conversion factors. Value of the following measurements are given as follows: MASS 1kgLENGTH 1mTIME 1sFORCE…
25 Feb 2022 12:33 PM IST
Assignment 3-2D Element Formulation Challenge
Assignment 3-2D Element Formulation Challenge Objectives: - Perform the simulation on the given model with default properties and change the properties. Compare both CASE 1 & CASE 2. Also, give a detailed explanation of hourglass energy. Recommended properties: Parameters Comment Ishell =24…
15 Feb 2022 10:12 AM IST
Assignment 2-RADIOSS Engine File Editing & 3D Meshing Challenge
Assignment 2 RADIOSS Engine File Editing & 3D Meshing Challenge Objective: - 1. Check the material properties of the rail component and calculate the speed of sound in steel rail? 2. The length of the rail is about 1000 mm. calculate the time it takes for a shock wave to travel from one end of the rail to…
06 Feb 2022 05:43 PM IST
Assignment 1-2D Meshing Challenge
Assignment 1-2D Meshing Challenge Aim: - Extract mid-surface and mesh the components. Objectives: - Clean the geometry. Extract mid-surface. Clean mid-surface geometry. Ignore holes less than diameter 5 mm. Create 2D mesh with target length 5 mm, min 3.5 mm, max 7 mm. And assign proper thickness,…
28 Jan 2022 12:38 PM IST
Project - 2 - Meshing on the suspension Assembly
Project - 2 Aim: - Meshing on the suspension Assembly Objectives: - For the given assembly, check for the geometrical errors and mesh with the given element Quality criteria. After meshing the component, the thickness has to be assigned for mid-surfaces. Use tetra elements to model non-uniform thickness components. Also…
22 Jan 2022 11:45 AM IST
Project 1 - 2D meshing on the instrumental Panel
Project 1 Aim: - 2D meshing on the instrumental Panel Objectives: - For the given component, check for the geometrical errors and mesh with the given element Quality criteria. After meshing the component, the thickness has to be assigned. Write a detailed report on your meshing process and also mention which method…
11 Jan 2022 11:20 AM IST
Week - 4 - 2D meshing for Plastic components
Objectives:- Create a mid surface by manual method and mesh the given model with given criteria and also give specific thickness to each component. S. No Quality Criteria Value 1 Target/Average length 1 2 Minimum Length 0.5 3 Maximum Length 3 4 Aspect 3 5 Warpage…
09 Jan 2022 10:26 AM IST
Week - 8 - Morphing
Objective:- CASE 1:- Perform morphing on the given component. CASE 2:-Perform morphing for the Model-2 and Increase the Height of the Dog houses and ribs. Morphing:- ANSA encompasses a full – fledged Morphing menu which is completely integrated with ANSA’s interface and doesn’t require any additional…
28 Dec 2021 06:56 PM IST
Week- 7 - Batch mesh and casting
Objectives:- Perform Manual, Batch, and Casting method for given component with given quality criteria and with good mesh flow. Sr. No Quality Criteria Value 1 Target/Average length 3 2 Minimum Length 1 3 Maximum Length 5 4 Aspect 3 5 Warpage 15 6 Skewness 45 7 Jacobian …
28 Dec 2021 10:52 AM IST
Week- 5 - Solid meshing
Objectives:- Perform the tetra meshing on the Rear view mirror component with given quality criteria. S. No Quality Criteria Value 1 Target/Average length 1 2 Minimum Length 0.5 3 Maximum Length 2 Use tetra elements to mesh the Volumes defined in…
11 Dec 2021 02:41 PM IST
Week 3 - 2D meshing for sheet metal
Objectives:- For the given Hood model, Take the mid surface for all the components after checking the geometrical errors and mesh the mid surface with the given element Quality criteria. (Refer the table Below for the Quality criteria) S.No Quality Criteria Value 1 Target/Average length …
29 Nov 2021 11:11 AM IST
Week 12:Project 2-Meshing of Rear Wheel Holder challenge
Objective:- Meshing the Rear wheel holder and assign the thickness. Procedure:- 1.Firstly,Import the IGES file. 2.Check the geometry and delete the solid if any. 3.Now, take the mid surface by manual method. 4.Mid surface of the geometry. 5.Then , toggle the unnecessary lines and remove the buttons. …
20 Oct 2021 09:59 AM IST
Week 12:Project-1-Meshing of Door Inner Panel Challenge
Objectives:- Create a mid surface by manual method and mesh the model with given criteria and also give specific thickness to each component. Procedure:- 1.Firstly,Import the given model / iges file. 2.Given model are as follows:- 3.Trim the model in four parts. 4.Now, remove the…
10 Oct 2021 09:38 AM IST
Week 9-Creation of 1D Connectors Challenge
Objective:- To mesh the given model and create 1D,2D connector to each parts by given data as follows: 1. Right_Rail_2 & Front_truss_1:- Seam-Quad(angled+capped+L) 1.1.Front_truss_2 & Right_rail_2:- Seam-Quad(angled+capped+L) 2. Left_Rail_2 & Front_truss_1:- Quad elements …
11 Sep 2021 11:32 AM IST
Week 8-3D Tetra Meshing Challenge
Objectives: 1. Create a Tetra mesh for the given geometry. Procedure: 1.Firstly, import the geometry & select the file type STEP. 2.Clean the following geometry manualy. 3. Now,by using the toggle,we toggle the lines where the meshing is failed. 4.Then, go to 2D meshing and mesh the geometry with…
02 Sep 2021 10:15 AM IST
Week 6-Meshing of Hood Challenge
Objectives:- To mesh and extract the mid-surface of the given component. Procedure:- Firstly, import the geometry from the folder. Now, select the latch_enforcement_extract Then, delete the solid of component. [Command: Delete>>solid>>delete entity] [Command: Geometry>>midsurface>>select surface>>Extract]…
21 Jul 2021 10:03 AM IST
Week 4-1D Element Creation Challenge
Objectives: To create 1D element on the given component with given cross-section and DOF using Hypermesh. a. Rod element:- Translational DOF should be Constrained with RBE2 link Cross-Section: BOX- Dimension a= 12 mm …
29 Jun 2021 07:04 AM IST