AIM: Simulate the flow over a cylinder and explain the phenomenon of Karman vortex street. Understanding the vortex shedding for different Reynolds numbers by changing the inlet velocities accordingly. Create a monitor point behind the cylinder at a distance 4 times the diameter which can be used to calculate and analyze…
KURUVA GUDISE KRISHNA MURHTY
updated on 19 Aug 2022
Project Details
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Read more Projects by KURUVA GUDISE KRISHNA MURHTY (26)
Week 10 - Simulating Combustion of Natural Gas.
COMBUSTION Combustion is defined as a chemical reaction in which a hydrocarbon reacts with an oxidant to form products, accompanied by the release of energy in the form of heat. Combustion manifests as awode domain during the design, analysis, and performance characteristics stage by being an integral part of various…
08 Nov 2022 07:38 PM IST
Week 9 - Parametric study on Gate valve.
Theory: Introduction: Gate valves are designed for fully open or fully closed service. They are installed in pipelines as isolating valves and should not be used as control or regulating valves. Operation of a gate valve is performed doing an either clockwise to close (CTC) or clockwise…
07 Nov 2022 05:07 PM IST
Week 12 - Validation studies of Symmetry BC vs Wedge BC in OpenFOAM vs Analytical H.P equation
Angles to test: `theta=10^0` `theta=25^0` `theta=45^0` Expected Results Validate Hydro-dynamic length with the numerical result Validate the fully developed flow velocity profile with its analytical profile Validate maximum velocity and pressured drop for fully developed flow Post-process Shear stress and validate…
06 Nov 2022 06:53 AM IST
Week 6 - CHT Analysis on a Graphics card
Your Objectives: Run the simulation by varying the velocity from 1m/sec to 5m/sec for at least 3 velocities and discuss the results. Find out the maximum temperature and heat transfer coefficient attained by the processor. Prove that the simulation has achieved convergence with appropriate images and plots. Identify potential…
31 Oct 2022 01:50 PM IST
Week 11 - Simulation of Flow through a pipe in OpenFoam
Simulation of Flow through a pipe in OpenFoam Aim: To simulate the axe symmetric flow in a pipe through openfoam. Objective: Validate Hydro-dynamic length with the numerical result Validate the fully developed flow velocity profile with its analytical profile Validate…
31 Oct 2022 04:55 AM IST
Week 5 Challenge : Surface wrap on Automotive Assembly
Surface wrap on Automotive Assembly Aim: To merge the different models and perform surface wrap on the models. Procedure : First the model is loaded on to ANSA Unwanted surface are deleted without damaging the outer shape of the geometries. Single cons are resolved mainly here as it would affect negetively on the…
26 Oct 2022 05:16 AM IST
Week 4 Challenge : CFD Meshing for BMW car
CFD Meshing for BMW car For the given model, check and solve all geometrical errors on half portion and Assign appropriate PIDs. Perform meshing with the given Target length and element Quality criteria. After meshing the half model, Do symmetry to the other side. Target lengths for the different parts of a model…
12 Oct 2022 04:45 PM IST
Week 3 Challenge : CFD meshing on Turbocharger
CFD meshing on Turbocharger AIM: This project aims to mesh a turbo charger for conducting CFD analysis. OBJECTIVE: The main objective of the given challenge is to perform surface mesh and volume mesh on turbo charger and also geometry clean up with the surface mesh for the PID's as Perform surface mesh with the given…
27 Sep 2022 07:17 AM IST
Week 4 - CHT Analysis on Exhaust port
Give a brief description of why and where a CHT analysis is used. Maintain the y+ value according to the turbulence model and justify the results. Calculate the wall/surface heat transfer coefficient on the internal solid surface & show the velocity & temperature contours in appropriate areas. How would you verify if…
25 Sep 2022 01:19 PM IST
Week 2 Challenge : Surface meshing on a Pressure valve
Surface meshing on a Pressure valve Check for the geometrical errors and perform Topology cleanup. Set three different target lengths as three different cases and mesh the model. Target length = 1mm, 3 mm and 5 mm (i.e., 3 cases). Element type to be used is triangular. Apply any one target length from…
19 Sep 2022 07:21 AM IST
Week 3 - External flow simulation over an Ahmed body.
Q1. Describe Ahmed's body and its importance. Q2. Explain the reason for the negative pressure in the wake region. Q3. Explain the significance of the point of separation. Expected Results: 1. Velocity and pressure contours. 2. The drag coefficient plot for a refined case. ( For velocity of 25m/sec,…
11 Sep 2022 09:06 AM IST
Week 8 - Simulation of a backward facing step in OpenFOAM
OBJECTIVE. To simulate an incompressible-laminar-viscous flow through the backwards-facing step geometry and perform a transient simulation. Case 1 - To Simulate the flow without using any grading factor (i.e., GF = 1) Case 2 - To Simulate the flow with a grading factor of 0.2. The cells…
23 Aug 2022 06:35 AM IST
Week 7 - Simulation of a 1D Super-sonic nozzle flow simulation using Macormack Method
Objective: To Simulate the isentropic flow through a Quasi 1D subsonic nozzle by deriving both the conservation and non-conservation forms of the governing equations and solve them by implementing the MacCormack's technique using MATLAB. Problem Statement: Determine the steady-state temperature…
22 Aug 2022 11:20 AM IST
Week 2 - Flow over a Cylinder.
AIM: Simulate the flow over a cylinder and explain the phenomenon of Karman vortex street. Understanding the vortex shedding for different Reynolds numbers by changing the inlet velocities accordingly. Create a monitor point behind the cylinder at a distance 4 times the diameter which can be used to calculate and analyze…
19 Aug 2022 05:26 AM IST
Week 5.1 - Mid term project - Solving the steady and unsteady 2D heat conduction problem
AIM: To solve 2D heat conduction equation for steady and transient state using various iterative techniques such as Jacobi, Gauss Seidel and Successive over relaxation methods using MATLAB. Problem Define; Heat conduction equation is define by the pde `(delT)/(delt)=alpha.(del^2T)/(delx)+(del^2T)/(dely)+(del^2T)/(delz)`…
10 Aug 2022 05:48 PM IST
Week 1- Mixing Tee
OBJECTIVE: For this challenge, we have created two versions of the mixing tee. One of them is longer than the other. Our job is to set up steady-state simulations to compare the mixing effectiveness when hot inlet temperature is 360C & the Cold inlet is at 190C. Use the k-epsilon and k-omega…
10 Aug 2022 10:33 AM IST
Week 3.5 - Deriving 4th order approximation of a 2nd order derivative using Taylor Table method
Object: Derive the following 4th order approximation of the second-order derivative using:- Central difference Skewed right-sided difference Skewed left-sided difference Also, prove that your skewed schemes are fourth-order accurate. Write a program in Matlab to evaluate the second-order derivative of…
18 Jul 2022 11:40 AM IST
Project 2 - Rankine cycle Simulator
Object: Creating a Rankine Cycle Simulator & Calculating the state points of the Rankine Cycle based on user inputs. Plotting the corresponding T-S and H-S plots for the given set of inputs. Theory: The Rankine cycle is an idealized thermodynamic cycle of a constant pressure heat engine…
24 May 2022 12:39 PM IST
Project 1 - Parsing NASA thermodynamic data
Object: To write a MATLAB program to parse the NASA thermodynamic data file. Calculate htermodynamics properties of various gas species Plot the Specific heat(CP),Enthalpy(H) and Entropy(S) for the local temperature range specific for each species. Theory: Parsing: Parsing a file means reading in a data stream of…
23 May 2022 11:10 AM IST
Week 4.1 - Genetic Algorithm
Object: Write a code in MATLAB to optimise the stalagmite function and find the global maxima of the function. Clearly expalin the concept of genetic algorithm in your own words and also explain the syntax for ga in MATLAB in your report. Make sure that your code gives the same output, even if it is made to run several…
06 May 2022 12:57 PM IST
Week 3 - Solving second order ODEs
Object: Your objective is to write a program that solves the following ODE. This ODE represents the equation of motion of a simple pendulum with damping Code: clear all close all clc b=0.05; g=9.81; l=1; %length is m m=1; %mass is kg %Initial condition theta_0=[0;3]; %time point t_span=linspace(0,20,150); %Slove…
19 Apr 2022 08:18 AM IST
Week 2- 2R Robotic Arm Challenge
Object: write a program in Matlab to simulate the forward kinematics of a 2R Robotic arm and Create an animation file of the plot Code: clear all close all clc %input l1=1; l2=0.5; theta1=linspace(0,90,10); theta2=linspace(0,90,10); ct=1; for i = 1:length(theta1) THETA1=theta1(i); for j=1:length(theta2) THETA2=theta2(j);…
07 Apr 2022 05:34 AM IST