PROJECT 1: PART-MODELLING, ASSEMBLY AND PHOTO-REALISTIC RENDERING OF AMERICAN CHOPPER               OBJECTIVE: To do the part-modelling of all the parts of American Chopper in SolidWorks software. Get the knowledge of how to assemble all the parts of Chopper. Do the photo-realistic…

PART-MODELLING OF LUXURY YACHT, ASSEMBLY AND PHOTO-REALISTIC RENDERING OF THE YACHT AIM:  To model the sunseeker predator yacht using SolidWorks Software. OBJECTIVE: Modelling of all the parts of luxury yacht and assemble the parts of the same. Learn how to setup the blueprints for modelling of part. Understand the…

  Aim: To perform the non-linear dynamic analysis of sheet metal during the punching operation in SolidWorks. Objective: To analyze the stress, strain and displacement which are developed in sheet metal (plate) during the simulation of the CAD model for the punching operation. Introduction: Myself Keval N. Patel.…

Aim: To perform a simple buckling test on a cyclonic separator stand in SolidWorks Simulation. Objective: To do the buckling analysis on cyclonic separator stand using two different cases: Case 1: The first buckling study will be performed without any stiffener. The main purpose of performing this analysis is to know how…

Aim: To perform the drop test SolidWorks Simulation Objective: To do the drop test of a  Printed circuit board (PCB) and analyze the results in SoliWorks Simulation. Introduction: Using the SolidWorks Simulation we can measure the accelerations i.e. g force developed within the product. In drop test analysis, the…

Aim: To create the CAD model of Internal Geneva mechanism and to study the motion analysis for obtaining contact force and angular displacement. Geneva Mechanism: Geneva mechanism is commonly used indexing mechanism where an intermittent motion is required. The design and fabricating of a conventional Geneva mechanism…

 Aim: To do the motion analysis on the planetary gear/epicyclic gear train. Introduction: A Planetary gear consists of a ring gear, sun gear and planet gears. In an epicyclic or planetary gear train, several spur gears (planet gears) are distributed evenly around the sun gear. The planet gears are meshing internally…

MOTION ANALYSIS OF PISTON ASSEMBLY Aim: To create CAD model of all the parts of piston assembly and assemble all the parts. To do the analysis using 3 different conditions.   Sr no Wrist pin offset (mm) Crank speed (rpm) 1. No offset 2000 2. 10 mm positive offset 2000 3. 10mm negative offset 2000   Wrist pin…

Abstract: In this project “Multibody Dynamics of IC Engine Valve Train”, the modelling of different parts of valve train are modelled in SolidWorks software and assembled them. After the assembly the Motion Analysis has been done to obtain the Valve lift and the contact force was found out between (i) the cam…

Aim: To do the Surface modelling of Aston-Martin One-77 Introduction: The Aston-Martin One-77 is a two-door, two-seater sports car built by the British car manufacturer Aston-Martin. In this project we are going to model the car in SolidWorks 2021(student edition) using the Surfacing and Solid Modelling (Hybrid-Modelling).…

Modelling of Boeing-747 in SolidWorks Objective: To model the various parts of Boeing in SolidWorks Assembly of Modelled parts Rendering of the Assembly Introduction: The Boeing 747-8 is a passenger airplane manufactured in the United States. It can accommodate 700 passengers if a single-class system is followed, while…

Aim: To do the simulation of pipe flow using line probes in SolidWorks Flow Simulation Objective: Run a pipe flow simulation with an inlet Reynolds number of 100,1000 and 10000. For each of these cases do the following: Place line probes at 95%, 90% and 85% of the pipe length. Compare the normalized velocity profile at…

Aim: To do the transient flow simulation over the cylinder in SolidWorks. Objective: The main objective of this project is to peform the Flow Simulation over a cylinder in SolidWorks. To obtain the value of Reynold's number using the given inlet velocity of fluid = 10 m/s With the obtained value of Reynold's number from…

Aim: To do the Flow simulation over a NACA 0017 Airfoil in SolidWorks Objective: To create the wing section needed for SolidWorks Flow Simulation Insert the curve of NACA 0017 airfoil Create the extruded model of Airfoil Setting up a Flow Simulation project for external flow  To run the calculations for various Angle…

Project link:   https://skill-lync.com/student-projects/flow-simulation-over-an-naca-2412-airfoil

Benchmarking Benchmarking is a process involving a structured comparison between similar products, services or processes on some dimensions of performance. For example, it can be used to compare the availability and delivery of features in a product. The main purpose of benchmarking is to improve the quality of existing…

Underbody Coating: In Indian road conditions, a cars underbody is affected by corrosion and also wear and tear caused by muddy water, bad roads, stones and other obstacles on the road To prevent this underbody coating provides long term protection from corrosion to car’s underbody. It also helps to protect parts…