All Courses
All Courses
Courses by Software
Courses by Semester
Courses by Domain
Tool-focused Courses
Machine learning
POPULAR COURSES
Success Stories
AIM: TO DRAFT VARIOUS GEOMETRIES USING CHAMFER,FILLET TOOL IN AUTOCAD. INTRODUCTION: In this geometries we are going to use various tools like chamfer, fillet and command like circle, line, mirror, trim, move, rotate,etc. 1)Drafting Decimal Drawing. PROCEDURE: 1.New Sheet-Set unit UN enter-Decimal-Precision 0.00-Meter-Ok.…
Samiksha dhole
updated on 29 Jun 2022
AIM: TO DRAFT VARIOUS GEOMETRIES USING CHAMFER,FILLET TOOL IN AUTOCAD.
INTRODUCTION: In this geometries we are going to use various tools like chamfer, fillet and command like circle, line, mirror, trim, move, rotate,etc.
1)Drafting Decimal Drawing.
PROCEDURE:
1.New Sheet-Set unit UN enter-Decimal-Precision 0.00-Meter-Ok.
2.Set Limit-0,0 and 420,210.
3.Zoom all.
4.Select Line form command and draw line of length 3 units form base line,@2.12<45,@2.83<135,@2<180 and close.
5.Draw circle at distance x=1.50,y=1.00 of diameter 1.20 and at distance x=1.50,y=2.50 of diameter 0.80.
6.Give dimension to all line segments,circle using annotate.
2)Drafting Architectural Drawing.
PROCEDURE:
1.New Sheet-Set unit UN enter-Architectural-Precision 0'0"-Feet-Ok.
2.Set Limit-0'0" and 12'-0",9'-0".
3.Zoom all.
4.Select Line form command and draw line of length 8'-0" units,@1'-9"<270,@2'-5"<270 and close.
5.Select Line form command and draw line form 2'-5"of length@3'<300 ,@2'-6"<30, draw the line form line 1'-9" @2'10"<225 and close.
6.Join the line 2'-10" and 2'-6".
7.Give dimension to all line segments using annotate.
3)Drafting Engineering Drawing.
PROCEDURE:
1.New Sheet-Set unit UN enter-Engineering-Precision 0'-0"-Feet-Ok.
2.Set Limit-0'0" and 12'-0",9'-0".
3.Zoom all.
4.Select Line form command and draw top line of length 2'-6.5",3'-3"<270, 5'-0.1"<0,1'-6" and close.
5.Select circle form command and draw circle at x-distance 1'-6" and y-distance 1'-3".
6.Give dimension to all line segments,circle using annotate.
4)Drafting Decimal Drawing.
PROCEDURE:
1.New Sheet-Set unit UN enter-Decimal-Precision 0.00-Meter-Ok.
2.Set Limit-0,0 and 420,210.
3.Zoom all.
4.Select Line form command and draw line of length 3 units form base line, 0.5 -ve y axis, 2.50 +ve x-axis, 2.50 +ve y-axis, 2 -ve x-axis, 3 +ve y-axis, 2.50 -ve x-axis, 2 -ve y-axis, 1 -ve x-axis, 3 -ve y-axis.
5.Give dimension to all line segments,circle using annotate.
5)Drafting Decimal Drawing.
PROCEDURE:
1.New Sheet-Set unit UN enter-Decimal-Precision 0.00-Meter-Ok.
2.Set Limit-0,0 and 420,210.
3.Zoom all.
4.Select Line form command and draw line of length 11.50 units form base line, 6 +ve y axis, 11.50 -ve x-axis, 6 -ve y-axis, Press Esc.
5.Select Line form command and draw line form midpoint of 11.50 of length 2.75 form both side.
6.Draw circle of diameter 3 form midpoint of line 11.50.
7.Draw circle of diameter 1 and 2 at distance of 4.25 form midpoint at both side.
5.Give dimension to all line segments,circle using annotate.
6)Drafting Decimal Drawing.
PROCEDURE:
1.New Sheet-Set unit UN enter-Decimal-Precision 0.00-Meter-Ok.
2.Set Limit-0,0 and 420,210.
3.Zoom all.
4.Select Line form command and draw line of length 2 units form base line, 1.5 +ve y axis, 0.50 -ve x-axis, 1 -ve y-axis, 1.5 -ve x-axis, 0.5 -ve y-axis Press Esc. Join the line.
5.Select Line form command and draw line of length 2 @x-axis,1.5@y-axis,2@-x-axis,1.@-y-axis.Command offset at distance 0.50 divide by 1 line at y-axis and divide into 3 parts form x-axis.
6.Select Line form command and draw line of length 1.5 @x-axis,1.5@y-axis,1.5@-x-axis,1.5@-y-axis.Command offset at distance 0.50 divide by 3parts at y-axis and divide into 1 line form x-axis.
7.Give dimension to all line segments using annotate.
7)Drafting Decimal Drawing.
PROCEDURE:
1.New Sheet-Set unit UN enter-Decimal-Precision 0.00-Meter-Ok.
2.Set Limit-0,0 and 420,210.
3.Zoom all.
4.Select Line form command and draw line of length 210 units form top line, 100<270, 75<270 Press Esc. Draw circle of diameter 50 and radius 35 at length of 100 and draw circle of diameter 30 and radius 25 at length of 75.Press Esc.Select fillet form command line select the radius of 15 and fillet both the corner.
5.Select Line form command and draw line of length 70<0 at the distance of 20 form top line, 40<270, 70<0, 40<90, and draw line at distance @10 y-axis. Press Esc. Select Line form command and draw line of length 70<0 at the distance of 120 form top line, 40<270, 70<0, 40<90, and draw line at distance @10 y-axis.
6.Draw the line at distance of 20 joining the circle form the rectangle formed.Press Esc.
7.Select fillet form command and select radius 20 and fillet the circle of radius 35.
8.Select fillet form command and select radius 6 and fillet the circle of radius 25.
9.Give dimension to all line segments,circle using annotate.
8)Drafting Decimal Drawing.
PROCEDURE:
1.New Sheet-Set unit UN enter-Decimal-Precision 0.00-Meter-Ok.
2.Set Limit-0,0 and 420,210.
3.Zoom all.
4.Select circle command and draw circle of diameter 0.90 and radius 0.90.
5.Command copy and copy both circle specify base point of circle and copy at distance of 8.55.
6.Select circle command and draw circle of diameter 4 and 5 form the midpoint of distance 8.55.
7.Draw the 4 tangent line on each side of circle.
8.Trim half the inside circle of both the outer circle.
9.Give dimension to all line segments,circle using annotate.
9)Drafting Architectural Drawing.
PROCEDURE:
1.New Sheet-Set unit UN enter-Architectural-Precision 0'0"-Feet-Ok.
2.Set Limit-0'0" and 12'-0",9'-0".
3.Zoom all.
4.Draw circle using circle command of radius 8' and at the distance of 32'-6" draw circle at radius of 9'.
5.Select arc (start,end,radius) select start point and end point and specify the radius 41'8" for top side and specify radius 20'10" for bottom side using same command.
6.Trim extra part of arc and circle.
7.Give dimension to all line segments,circle using annotate.
10)Drafting Decimal Drawing.
PROCEDURE:
1.New Sheet-Set unit UN enter-Decimal-Precision 0.00-Meter-Ok.
2.Set Limit-0,0 and 420,210.
3.Zoom all.
4.Draw rectangle of 4.4x4.4m select offset at distance of 0.2.
5.Rotate rectangle at 45 degree specifying base point center and copy.
6.Trim unwanted part.
7.Give dimension to all line segments using annotate.
11)Drafting Architectural Drawing.
PROCEDURE:
1.New Sheet-Set unit UN enter-Architectural-Precision 0'0"-Feet-Ok.
2.Set Limit-0'0" and 12'-0",9'-0".
3.Zoom all.
4.Select Line form command and draw line of length 9'<270, @3'<180, @4'-6"<270, @4'-6"<180, @1'-2"<90, @5'-2"<180, @1'-2"<270, @4'-6"<180, @4'-6"<90, @3'<180, @9'<90, @3'<0, @2'-8"<45, @2'-8"<45, @5'-3"<0, @3'-7"<30, @3'-7"<30 and close.
5.Select Line form command and draw line form 6'-9" at center of length @3'<45, mirror line on remaining 3 side of rectangle.
7.Give dimension to all line segments using annotate.
RESULT:
All drawing are draft according to the given drawing with proper annotation, precision and using command like fillet, trim, rotate, mirror, circle, line using Autocad.
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
To Generate report for Steel Industrial and RC structures using TSD
AIM:- to generate the report for the steel building design Procedure:- Open the Tekla model Now go to report option from the ribbon and select model report Now select the load cases and combinations summary to obtain report Click on the show report to obtain report We can change the project name , address…
30 Dec 2022 11:47 AM IST
To Design slab and foundation for an RC residential building using TSD
1.Design the slab and foundation of the model. Outline the thought process for designing of the elements (column, beam, slab and foundations) Aim - To design the slab and foundation of the model. Tools Used - 1st Order analysis, Analysis all ( static ), Status , check panel ,Properties window etc. Procedure - Open the…
30 Dec 2022 11:35 AM IST
To Design RC column and beam for RC residential structure using TSD
Aim:- To run the analysis of the structure and design reinforced concrete beam and column procedure:- open the tekla model and run the analysis now select any of the column member and right click on it then select the interactive design from the given option check whether the member is passing through all the design…
30 Dec 2022 11:19 AM IST
To Generate seismic loading based on IS code and to run the analysis using TSD
1.Generate seismic loading based IS codal provisions and zone II. Any other data you can assume and input accordingly Aim: To generate seismic loading based IS codal provisions and zone II. Procedure: Open the previously save Tekla model Now go to the load cases and add the seismic load case, and click ok Now go…
21 Dec 2022 08:25 AM IST
Related Courses
Skill-Lync offers industry relevant advanced engineering courses for engineering students by partnering with industry experts.
© 2025 Skill-Lync Inc. All Rights Reserved.