1) concrete mix design for M35 grade concrete with fly ash  From table 8 of IS456, Target mean strength fck'= fck+ 1.65s= 30+ 1.65*5= 38.25n/mm2 From table5 of is456:2000, we have for m35 grade concrete w/c ratio= 0.45. by experience take w/c ratio = 0.40. From table2 of is10262:2009, water content for maximum nominal…

1)AIM AND INTRODUCTION: To draw a g+1 residential floor plan as per vastu shastra and calculate the loads as per IS CODE. Vastu is a part of civil engineering as the ancient engineer Vishwakarma words it is said that the vastu is used in every part of civil structure, and it has no expire date. Now a day’s civil…

AIM: To create the geometries from p1 to p2 using all the coordinates system methods. ABSOLUTE COORDINATE SYSTEM. RELATIVE COORDINATE SYSTEM. POLAR COORDINATE SYSTEM. INTRODUCTION: Using the absolute coordinate system and relative coordinate system, polar coordinate system. Click the AutoCad icon from desktop and go to…

AIM:    To draw C.S of load bearing wall over spread footing using AutoCAD Software  PROCEDURE: Open AutoCAD  In the command prompt type QNEW click on imperical template , advaced setup , decimal  In the command prompt type units  Type= decimal, precision = 0.00 , angle = decimal…

            AIM:   To draw the given drawing using AutoCAD software  PROCEDUE :   STEP 1:  In the command prompt type Units and select decimal unit    STEP 2 :  In the command prompt type PL ( Polyline )  In the command prompt specify start point…

Aim - Sketch the layout of a residence plan, seating plan and plan for toilet & utility room in Autocad given in the question sheet. Sketch the layout of a residence plan, seating plan and plan for toilet & utility room in Autocad given in the question sheet.  Instructions common to all drawings:…

Aim of the project: To draw the  plan along with the  sections with appropriate dimensions. The drawing in the project is done with help of AUTOCAD software.  Procedure:   Step 1: The units of the drawing sheet is set to Engineering precision. Step 2: Construction line in horizontal and vertical…

Aim of the project: To Create the templates as shown in Figures, Create the doors type for warehouse as shown in the Figure,Create each symbol as a block with the name given in the legend,  Create the door type for residential building as a block, Create each shape as a block as shown in the Figure.…

Aim of the project: To create layout of the drawings created a few weeks in the challenges. Procedure: Step 1: The layout as per mentioned is selected i.e., Tutorial.mArch.dwt from the templates existing Step 2: The view ports are created as per the sizes mentioned and the drawing is adjusted in the view port to view the…

Aim of the project: To create layout of the drawings created a few weeks in the challenges. Procedure: Step 1: The layout as per mentioned is selected i.e., Tutorial.mArch.dwt from the templates existing Step 2: The view ports are created as per the sizes mentioned and the drawing is adjusted in the view port to view the…

Q1) AIM :  Create a 3D Furniture element as shown in the Figure. Assume dimensions which are missing. PROCEDURE :  open the autocad ,and chanage the view cube to home in order to get 3d figure. invoke the line command by pressing l enter and draw a vertical line of 2'6 , followed by line of 3 feet in the next…

Aim of the project: To draw the given drawingss in 3d along with the given sections with appropriate dimensions. The drawing in the project is done with help of AUTOCAD 3d software.  Procedure:   Step 1: The units of the drawing sheet is set to Engineering precision. Step 2: Construction line in horizontal…

Aim of the project :- To draw the 3D residential building and to create the rendered view Introduction :- The general commands used for drawing the building is as follows :   Line Polygon Rectangle Circle Erase Copy Trim Offset Extend Move Rotate Dimension Text Fillet Extrude 3D Rotate Etc The drawing in the…

AIM- to carryout various projects from q1 to q10 as given above using revit software and its various tools like ceiling, roofs, multiple views, project information, architectural and structural plan etc and execute the same PROCEURE:   1) Based on the project saved from Week 3, proceed from the First Floor Level.…